BASCOM-AVR : Avr doesn't start (boot) : REPLY
If you have the low byte fuses set to CKSEL0 = 1 and SUT = 11 then you already have 16K clock cycles plus 65 ms delay between power up and reset. See table 5 on page 25 of the Atmel datasheet. I...
View ArticleBASCOM-AVR : lookup table statement problem : REPLY
sorry surely i have put it in bascom data not date but when i wrote the topic i mistakenly wrote it date anyway : if i put : data 3,3,5,56,6,6 data 89,5,5,4,3,3 does 89 will have the index 6 ??
View ArticleBASCOM-AVR : lookup table statement problem : REPLY
[quote:f893220425="majd-ghadab"]does 89 will have the index 6 ??[/quote:f893220425] Yes.
View ArticleBASCOM-AVR : Avr doesn't start (boot) : REPLY
Hi Guys, @plons ... I do hope that o-family (the creator of the lcd driver), took the 450 ns in account. @ardianj ... I will take one of the units home and stay on the problem because i'm also not...
View ArticleBASCOM-AVR : KS0108 Display: Trouble with higher clock speed : REPLY
You need to answer condition correctly to a question. Otherwise, neither the following test method nor advice can be proposed. O-Family
View ArticleBASCOM-AVR : Avr doesn't start (boot) : REPLY
The library which I corrected has given the margin of 1uS to the pulse width of E clock. If pulse width is unusual, you are wrong in the frequency of a system clock, and the preset value of $CRYSTAL....
View ArticleBASCOM-AVR : Avr doesn't start (boot) : REPLY
7805 has been used for ages. Used with proper decoupling, I see no reason to replace it with a 317. Any news on the current consumption ?
View ArticleShare your working BASCOM-AVR code here : Meet the Helios : REPLY
I picked up a Arduino Leonardo and got it working with the Arduino IDE. I tried the two Arduino programmer options in Bascom but neither worked. Does anyone know how to program a Leonardo board? Or...
View ArticleBASCOM-AVR : simple spi soft problem : NEWTOPIC
hello, in order to understand well the SPI protocol I did 2 programs working on the same dev card: 1 Atmega644A as master, 1 atmega 168 as slave I doesn't want (for now) use the hard SPI protocol for...
View ArticleEASY TCP/IP : W5100 webserver sample : NEWTOPIC
I'm trying to get the W5100 Webserver sample program working but I'm having a problem. Watching on a terminal program, I see the "done" output after the Config TCPIP command but then it seems to...
View ArticleEASY TCP/IP : W5100 webserver sample : REPLY
Here I am answering my own question. I had to add the chip select to the TCPIP Config command and change the Config to Noint. Seems to be working fine now. Thanks, Bob
View ArticleBASCOM-AVR : simple spi soft problem : REPLY
the fault is that the SPI is configures for master SPI. If you want to do a SPI soft slave check out the spi-softslave.bas sample from samplesSPI.
View ArticleBASCOM-AVR : Spi-compatible SPI interface : NEWTOPIC
Hello, Many Texas-Instruments devices (ADS1291 for instance) provide a "SPI-compatible SPI". Usually, SPI has Miso and Mosi, but that has DI and DOUT. Does anybody have experience with that? Regards,...
View ArticleAVR : AVR leaching power from serial line : REPLY
Just a follow up on this issue with power. I've been running the circuit non-stop for a month now and the problems are gone. The combination of putting current limiters on the serial lines and enable...
View ArticleBASCOM-AVR : Socketstat strange results???? : NEWTOPIC
Warning long post...... Going to try and explain this anomaly without flooding with too much detail but yet enough to show the problem. Basis of problem: Socketstat is indicating that there is more...
View ArticleBASCOM-AVR : Spi-compatible SPI interface : REPLY
MOSI (Master Out Slave In) becomes DI (Data In) on the slave device. MISO ( Master In Slave Out) becomes DO or DOUT (Data Out) on the slave device.
View ArticleBASCOM-AVR : Socketstat strange results???? : REPLY
Sometimes this forum is just plain good therapy....... I have been working on this problem for several days. Once I type the above forum post, I started to realize what was happening. The server...
View ArticleBASCOM-AVR : KS0108 Display: Trouble with higher clock speed : REPLY
O-family, Sorry I missed your question. Yes it returns to normal after a push on the reset switch, but sometimes I have to push it several times? if I power down ( oscilloscope probe on reset (pin 9...
View ArticleEASY TCP/IP : Timer 0 ,2 : NEWTOPIC
Hi I know there are lots of posts and info about timers and interrupts but I have a problem with Timer 0 ,2 I use timer 1 as a pwm timer so that leave me Timer 0 or timer 2 for periodic system...
View ArticleBASCOM-AVR : KS0108 Display: Trouble with higher clock speed : REPLY
If a reset switch is effective during freezing, it does not have influence of a watch dog timer. If a multiple push is necessary for reset, I think that the reset of the LCD does not succeed. When...
View Article