EASY TCP/IP : Atmega32 and Wiznet W5100 : REPLY
See my question above and here [quote:a62df29bae]What are you doing with the SPI_enable line of the WIZ810MJ? What have you done with the reset of the WIZ810MJ? [/quote:a62df29bae] Have you had a look...
View ArticleBASCOM-AVR : day of Week and Month : NEWTOPIC
Can anybody help my with a problem that I have to view the day and month. the day of the week is working but the month as a "word" will not work. my test code that I use is: (what's wrong) $regfile =...
View ArticleBASCOM-AVR : day of Week and Month : REPLY
Try this [code:1:93d25f1a96]Config Clock = Soft ' we use build in clock Config Date = Dmy , Separator = - ' ANSI-Format Enable Interrupts Dim Bweekday As Byte , Strweekday As String * 9 Dim Bmonthday...
View ArticleBASCOM-AVR : day of Week and Month : REPLY
Thanx Visovian It's so simple if you know how it works verry good
View ArticleBASCOM-AVR : Calculator percent error rate in the port : REPLY
You will have to be more specific. What baud rate and crystal frequency ? At most 'normal' baud rates, ie the ones 115300 baud and below, and with reasonable crystal frequencies, say 4MHz and above,...
View ArticleBASCOM-AVR : lib and obj : NEWTOPIC
Hi, The lib file contains object code. Is it that all avr, including xmega have same object code for respective instructions ? Otherwise universal lib file is not possible. Regards, Devidas...
View ArticleBASCOM-AVR : Calculator percent error rate in the port : REPLY
I know all this and understand it. No error, I now do not get, I want to know the future and take into account the moments of errors (because they are not immediately, but Immersed cumulative form, ie...
View ArticleBASCOM-AVR : lib and obj : REPLY
No Mark, Its a plain question. :) I really know very little about avr. Rather think I am bit lazy to find out. So I wrote in surprise. I looked into the lib files as you suggested, and their lbx...
View ArticleBASCOM-AVR : lib and obj : REPLY
- you really should read some data sheet. it contains good valuable information. - this forum is free, do not confuse it with official support - the object code is the same for all chips. it would be...
View ArticleBASCOM-AVR : SETTCP : NEWTOPIC
Does anyone know what format(s) can be used for the IP address with SETTCP? Can it take the LONG format? (It is not clear at all in BASCOM's help) I have seen in...
View ArticleBASCOM-AVR : Canbus Noob. Help Required please : NEWTOPIC
Hi I'm venturing out on a project with Canbus to link-up in a daisy chain fashion on a project. I'm using a off the shelf Chip45 Crumb128/Can module. The MCU is a AT90CCAN128 chip.I have had a bit of...
View ArticleBASCOM-AVR : Canbus Noob. Help Required please : REPLY
like the help says: the return value is the CANSTMOB register content. you can check the PDF to see what it means. for the can128 it means : Bit 0 AERR: Acknowledgment Error the sample must be...
View ArticleBASCOM-AVR : SETTCP : REPLY
Great! However I still get a "Invalid data type" error when compiling: Settcp Ip_address do I need to put the MAC, SUBMASK and GATEWAY parameters perhaps?
View ArticleBASCOM-AVR : Canbus Noob. Help Required please : REPLY
Thank you Mark, it is much appreciated
View ArticleBASCOM-AVR : SETTCP : REPLY
you need to provide all the parameters. when you only want to alter one you could check settcpregs
View ArticleBASCOM-AVR : Sample Electronics programmer not working in Win 7 : REPLY
in the mean time i also tested under WIN8. Using the new setup it installer properly. So the only problem : to find the proper base address. When you select sample electronics programmer, you can also...
View ArticleBASCOM-AVR : Sample Electronics programmer not working in Win 7 : REPLY
hi, I tried all combinations (9) of LPT1,LPT2,LPT3 and EFD8,EFD4,EFE0 and it would not program the chip. I also tried TEST pin #2 and it was always low, also pin #11 is always high (5v). Does this...
View Article