BASCOM-AVR : simple spi soft problem : REPLY
I did a simulation in Proteus and it worked out fine. I only changed some line (chose m644 since there is no m644A in proteus). I remarked 'Config Lcdmode = Port And in the slave i used : Config Spi =...
View ArticleBASCOM-AVR : Chip Hangs : NEWTOPIC
Hello, I have made about 200 boards with some code communicating via rs485 to another board and generally never had any of my atmega32 freeze. Just in the last 3 days 3 units froze on me. There was a...
View ArticleVarious : Please help to code Bascom : REPLY
I still have not Understand Setting DIPSWICT formula, whether it is derived from the number Binner?? And if it can be scaled again suppose Frequesi be 780-108 MHz. Thanks. [code:1:0e8a068df6]'( 100khz...
View ArticleVarious : Please help to code Bascom : REPLY
Hi, Yes the DIP SW set up a 0.100Mhz (100Khz) step its 8 bit so max steps is 255 (25.5Mhz) for 78Mhz - 108Mhz you need 30Mhz thats 300 steps so it can not be done in (8bit) the Dip SW is binary setup...
View ArticleBASCOM-AVR Old versions : Chip Hangs : REPLY
Hello joltz "Can the stacks hang a chip? " Yes! Make the values larger if you have ram left, read the help about the stack to understand what it is used for/by also look out for a divide zero problem...
View ArticleVarious : Please help to code Bascom : REPLY
If you like to use freq 78 - 108Mhz we can make this but you need to add a Dip SW to portd.0 for the 9 bit see addon "LM7001.rar" show the edit of pcb and code for it to dip sw settings is at bottom...
View ArticleVarious : Please help to code Bascom : REPLY
I am very grateful to the above explanation. if we move the sorce code for ATmega8 does affect the data communication?? because I had just ic ATmega8.
View ArticleVarious : Please help to code Bascom : REPLY
the PCB o9nly have support for ATTINY2313 (20pins) so how will you add ATMEGA8 (28 pins) ?
View ArticleVarious : Please help to code Bascom : REPLY
I do not mean to add, but in lieu of ATTiny2313 to ATMEGA8 does this work??
View ArticleVarious : Please help to code Bascom : REPLY
then you need to compare pins Tiny2313 vs M8 portb have Xtal on M8 change the setup of pins to make it run on M8
View ArticleVarious : Please help to code Bascom : REPLY
Ok thanks Mr.Kim .. I will start to try to establish his hadware.
View ArticleBASCOM-AVR : LINEINPUT : NEWTOPIC
Hi I want to perform a LINEINPUT from a text file - data saved by print command - but not from the first line but from the LAST line of the file and then the 2nd last and so on , use of UP DOWN...
View ArticleBASCOM-AVR : KS0108 Display: Trouble with higher clock speed : REPLY
You Solved the problem!! Thank you SO much! tried it on 2 different units now did 100 power down power up 100% ok Picture on display is ok what did you change? Wilfred.
View ArticleBASCOM-AVR : KS0108 Display: Trouble with higher clock speed : REPLY
It was good! There was your detailed report, thereby a bug to initialize the LCD of other model was found. I fixed it. O-Family
View ArticleBASCOM-AVR : Avr doesn't start (boot) : REPLY
Gentlemen, my problem is solved look here http://www.mcselec.com/index2.php?option=com_forum&Itemid=59&page=viewtopic&p=62910#62910 it was something in the LCD driver. Wilfred
View ArticleBASCOM-8051 : Automatic covertion to ASCII problem : NEWTOPIC
Hi, i'm new here :) I need to make a program but i have problems with ASCII converting... I need to input the key from number 1 to 100, but if i input letter key, it automatictly converts it to ASCII...
View ArticleBASCOM-AVR Old versions : Chip Hangs : REPLY
My hw,sw and frame size - 128......that is pretty big already for the atmega32A.....no? Could this division of an integer into a single variable be too taxing on these stacks? Are you sure the 99%...
View ArticleBASCOM-AVR : PWM for Sinus generator too low in frequency : NEWTOPIC
hello how can i make a sinus osc with the PWM with a frequency about 10khz? my prog here is good but only 1000hz! thanks for help ' Oscillateur Sinus en PWM '================================ $regfile...
View ArticleBASCOM-AVR : PWM for Sinus generator too low in frequency : REPLY
[quote:518e90fc33="Robert_Pre"]how can i make a sinus osc with the PWM with a frequency about 10khz?[/quote:518e90fc33] Use less support points. Assumed the ideal condition that after each 8bit PWM...
View ArticleBASCOM-AVR : PWM for Sinus generator too low in frequency : REPLY
Two more thoughts: You can switch to an Xmega, which can run at 32 MHz, giving you more clock cycles to work with. You can switch techniques on how you generate the sin wave. Right now you have a...
View Article